I’m starting a project titled “leftovers” inspired by this neat picture found on Reddit. It seemed a good fit for what I already had in my stash: the 1/35 Verlinden C19 Clark forklift and the 1/32 MicroAce Honda T360. I’ll also add a 3d-printed miniature raccoon looking into a trash bin, found on Etsy. Hope you’ll like it!
I’m finally making some progress on this project. I’ll show more shortly, but for now I wanted to share my broken back light! Folded tin foil from food packaging (thanks cats!) with some thin wire taken from the protective case of an old jack cable. 4×2 mm space is tough to work with.
I’m working on the N360, trying to make it look used and abused.
I had a vague memory (a made-up one?) of a truck whose box had been protected with planks, and decided to roll with it. I cut and glued balsa thin balsa wood, then used my X-Acto knife to add damages. I also needed nuts and bolts to hold those planks, and Meng 0.8mm ones worked just fine, although many flew into The Nothing…
The T360 is ready to go (actually, it’s primed already, but haven’t had time to take pictures). I’m happy so far with the progress I’m making on it.
To mimic corrosion, I mostly focused on the bottom of the body where I used a rotary tool to damage the plastic. I then drilled a few clusters of holes here and there, and then use my x-acto to connect the holes and damage the plastic some more. It was followed by a slurry of Tamiya putty mixed with Mr Leveler Thinner stippled over the damaged areas. Finally, I used Super Glue (gel) at the edge of the textured areas to mimic paint starting to crackle.
I went a bit heavy on the roof, so I covered the damages with some tin foil and used stretched sprue melted with plastic cement to reproduce the weld seams.
For the damaged light at the back, I drilled a hole, cleaned it up so a nice rectangle, and folded some tin foil to fit. I drilled a small hole into the foil and added three thin wires (0.25mm) that, I hope, look like the cables powering a light. A bit of a rough job, but I’m happy for first attempt at this kind of detailing.
Finally, for the tires, I first sanded the tread by turning them on the rotary tool. I then cut out a small part to show the tire flat, and then pressed it on a hot surface (a heated up spatula used for mudding). The technique was inspired by the work from Thomas at Laser Creation World.
It’s gonna stay on the side as I’m finishing the preparation of the forklift and the accessories.
I’m also done assembling the forklift. A simple kit, but a couple parts were warped and I had to straighten them, or, at least, I tried using very hot water (near boiling). After three atttempts, I decided it was enough, as I was afraid the pieces would break.
I added some signs of wear and tear here and there, although nowhere near what I did on the truck, since the reference picture shows both vehicles at different stages of abandonment. I started with the anti-slip plate below the driver’s seat: I sanded it, trying to focus on the centre, to make it look smooth, as it does after repeated uses.
For the wheels, I simply sanded an area that will become the surface in contact with the ground to mimic the weight of the vehicle.
And the most fun was trying to show a damaged padding on the driver’s seat: I carved some edges and cut tiny pieces of a makeup sponge that I glued with super glue. The pieces were trimmed further until I liked the result. Once the vehicle is painted, I will add some tape to mimic “repairs”.
Nice work on that little T360! I built one of these last year and really enjoyed it. I added a set of steelies from an 80’s Nissan wagon /135 from TomyTec. I usually build 1/24-1/25 cars but dabble in several other genres and scales and really had a good time with this one and bought a bunch more in 1/32.
Thanks! I like yours a lot; the switch to Tomytec wheels was a good call (the Nissan Sylvia is on my list!).
Those MicroAce kits are great, especially since they’re so original. They’re, however, getting old, and the level of details is low, although the overall quality is decent.
We’re underserved on modern-ish civilian kits, although I want to try one Aoshima 1/32 Snapkit cars: The range is quite good, and the most recent ones seem to be well detailed.
Thanks Francois! I have another 15-20 of these little 1/32 scale kits and while they’ve been around for a while, they still build up nicely and have enough detail to satisfy most of us. I’ve gotten a few of the little three wheelers from Daihatsu, etc as well as many others. I have Aoshima’s Nissan GT-R in 1/32 and will be painting it in Millenium Jade at some point.